User Tools

Site Tools


products:wizwiki_w7500:start_getting_started:write_firmware

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
products:wizwiki_w7500:start_getting_started:write_firmware [2015/05/21 10:28]
markyu [Examples Binany]
products:wizwiki_w7500:start_getting_started:write_firmware [2018/08/08 13:18] (current)
justinkim
Line 2: Line 2:
 Writing firmware into WIZwiki-W7500 has four ways.\\ Writing firmware into WIZwiki-W7500 has four ways.\\
   *Using the CMSIS-DAP (Drag and Drop)   *Using the CMSIS-DAP (Drag and Drop)
-  *[[:​products:​wizwiki_w7500:​start_getting_started:​write_firmware:​keil_cmsis_dap|Using the CMSIS-DAP]] (through ​keil+  *[[:​products:​wizwiki_w7500:​start_getting_started:​write_firmware:​keil_cmsis_dap|Using the CMSIS-DAP]] (through ​Keil uVision5
-  *Using the ISP+  *[[products:​w7500:​documents:​appnote:​isptool|Go to ISP tool manual & Program download]]
   *[[:​products:​wizwiki_w7500:​start_getting_started:​write_swd_debugger | Using the SWD Debugger]]   *[[:​products:​wizwiki_w7500:​start_getting_started:​write_swd_debugger | Using the SWD Debugger]]
  
Line 19: Line 19:
  
  
- 2. You drag and drop or copy the firmware to the removable disk, the firmware writing ​is completed.+ 2. You "drag and drop" ​or copy the firmware to the removable disk, the firmware writing ​progress has completed.
 {{ :​products:​wizwiki_w7500:​start_getting_started:​drap_n_drop.png| Drag and drop }}  ​ {{ :​products:​wizwiki_w7500:​start_getting_started:​drap_n_drop.png| Drag and drop }}  ​
    
- 3. After completing the firmware writing, ​check to open the removable disk.+ 3. After completing the firmware writing, open to check the removable disk.
  
  
- 4. If "​fail.txt"​ file is exists in the removable disk, it is writing the firmware failed.+ 4. If "​fail.txt"​ file is exists in the removable disk, it means writing the firmware ​has failed.
  
  
- ​5. ​The number two item attempts again, after pressing the Reset of the WIZwiki- W7500.+ ​5. ​ ​After ​pressing the Reset button (SW1) of WIZwiki- W7500, please repeat the steps from step 2.
  
 ---- ----
Line 34: Line 34:
 {{page>​products:​wizwiki_w7500:​start_getting_started:​write_firmware:​keil_cmsis_dap}} {{page>​products:​wizwiki_w7500:​start_getting_started:​write_firmware:​keil_cmsis_dap}}
  
-===== Using the ISP ===== +----
-**W7500 ISP Program** +
-  *{{{{:​products:​wizwiki_w7500:​w7500_isp_20150519_.zip| W7500 ISP Program Download}}+
  
-When W7500 is in the boot mode, firmware writing is possible via the ISP as WIZwiki-W7500 has a built-in ISP header. As ISP header supports the UART signals, you need a converter like TTL to RS232 or TTL to USB in order to connect to your PC.\\ +==== Reference ====
-Make configuration as shown below Block Diagram.\\+
  
-{{ :​products:​wizwiki_w7500:​getting_started:isp_block.png?​direct&​800 ​ISP Block Diagram}}  ​+  *[[:​products:​wizwiki_w7500:​start_getting_started:debugging_w7500#​set_flash_algorithm ​Set Flash Algorithm]]
  
 +----
  
-** To follow ** +===== Using the ISP ===== 
- +{{page>products:​wizwiki_w7500:​start_getting_started:write_firmware:ISP}}
-1. Run "​W7500_ISP (20xxxxxx) .exe"​.\\ +
-{{ :​products:​wizwiki_w7500:​getting_started:​isp.png?​direct&​800 | ISP Program}} +
- +
-2. To make WIZwiki-W7500 enter the Boot Mode, press the SW1 while keeping the SW2 pressed.\\ +
- +
-3. Select a device connected to the ISP header from "​Serial Port" and click "​Open"​. If you entered Boot Mode successfully,​ then "​Serial Open Complete"​ message will be printed on the status bar at the bottom of window.\\ +
-> **Before open button of ISP tool click, you have to test using the terminal windows. After serial port open using the terminal windows,​enter the capital "​U"​. If it is the ISP mode, you can see the returned character.** +
-{{ :products:​wizwiki_w7500:​getting_started:​isp_set.png?​direct&​800 | ISP Program Setting}} +
- +
-4. Click "​Browse"​ to select the binary.\\ +
-{{ :​products:​wizwiki_w7500:​getting_started:​isp_start.png?​direct&​800 | ISP Program Binary Select}} +
- +
-5. Click "ISP Start" button, then the firmware writing will be performed.\\ +
- +
-6. After the firmware writing completes, the window like below will pop up.\\ +
-{{ :​products:​wizwiki_w7500:getting_started:isp_complete.png?​direct&​200 | ISP Complete}}+
  
  
 ---- ----
 {{page>​products:​wizwiki_w7500:​start_getting_started:​write_swd_debugger}} {{page>​products:​wizwiki_w7500:​start_getting_started:​write_swd_debugger}}
products/wizwiki_w7500/start_getting_started/write_firmware.1432171727.txt.gz · Last modified: 2015/05/21 10:28 by markyu