User Tools

Site Tools


products:wiz750sr:commandmanual:start

WIZ750SR Command Manual

Supported Languages


WIZ750SR Command Overview

WIZ750SR provides various commands for the product’s setting and control. Each command is composed of a 2 byte alphabet character strings and all capital letters. By using these commands users can add script to the serial device or main MCU for product settings, and also can create a program1) for controlling the WIZ750SR module via network.

Each command can operate read/write depending on the parameter, and there is also a read only command2).

Entering the command and switching the command mode of the serial port device is done using the data UART port. The debug UART port is not supported for command entering or operation.

Identical 2-byte character strings is used for setting the product with commands via serial and Ethernet network, but there will a distinction of the sending frame form. Thus this document will cover explanations of all commands and guides for each sending methods and its form of frames.

The different command modes are as following.

Abbreviations

CR Carriage Return, moves the cursor to the far left(starting) position ('\r', 0x0D)
LF Line Feed, moves the cursor to the new line below ('\n', 0x0A)
N Number of commands
RW Read / Write
RO Read only
WO Write only

Usage of Command Set

Entering Serial Command Mode

You can use either of the two methods below to enter serial command mode.

  • 1. Enter command mode using hardware trigger pin
    • Use the HW_TRIG pin of the WIZ750SR (For the EVB, HW_TRIG switch) to enter command mode.
    • Upon turning the power on, check the pin to enter command mode. Use the trigger pin to re-enter the command mode when rebooting.
    • The trigger pin should be pull-up, and operates as low active.
    • This method is used when users wish to change settings while the product operation is initiated.
  1. Set the hardware trigger pin(HW_TRIG) to Low.
    • When using the EVB, place the HW_TRIG switch to Command.
  2. Power on the WIZ750SR.
    • When operating in serial command mode, users can check the following message via Debug UART port.
    • > SEG:AT Mode 
  3. Enter the Command and Parameter that needs setting via serial port3).
  4. Switch to data transmission mode(GW mode) using EX command.
    • If the switch to data transmission mode is successful, users can check the following message via Debug UART port.
    • > SEG:GW Mode 
  • 2. Enter command mode using command mode switch code4)
    • Users can enter command mode using the command mode switch code provided by WIZ750SR.
    • The command mode switch codes can be used only if it is enabled in the configuration tool. (default: Enabled)
    • The command mode switch code is composed of 3-byte Hex codes, and can be changed to a different value if needed. The code only accepts Hex value. (default: Hex [2B][2B][2B]5))
  1. Check if 'Serial command mode switch code' is enabled at the configuration tool and the 3-bytes 'command mode switch code'.
  2. Enter the ‘command mode switch code’ via data UART port to change modes.
    • Read below what you need to be cautious about when switching to command mode.
    • When operating in serial command mode, users can check the following message via Debug UART port.
    • > SEG:AT Mode 
  3. Enter the Command and Parameter that needs setting via serial port.
  4. Use EX command to switch to data transmission mode.
    • When operating in data transmission mode, users can check the following message via Debug UART port.
    • > SEG:GW Mode 

Please be cautious when using the trigger code to switch command mode.

  1. There has to be a time gap of at least 500ms at the start and end of the ‘command mode switch code’ in order it to be read as switch code.
  2. The entering time in between each byte of the ‘3-byte command mode switch code’ has to be below 500ms.
  3. Do not add CR or LF at the end of the command mode switch code6).
  4. The default values of 1 and 2 above are 500ms; these values change to the timer value if the timer value of the serial data packing option is set to a certain value.

Serial Command Frame Format

You must include CR and LF at the end of each command. CR and LF must be included at the end of each commands when multiple commands are entered simultaneously.

Get Request
[2-bytes Command Code] [CR] [LF]
  • Enter command without parameter.
  • The response relevant to the command will return.
Set Request
[2-bytes Command Code] [Parameters] [CR] [LF]
  • Enter the command and parameters you wish to set.
  • There will be no particular response and the field value relevant to the command will change instantly.
  • You have to use the SV command in order to save settings, and use the RT command to change IP allocation methods or other initial operation changes.

* Note: You can check the Echoback of UART command via EC command.


Command via Ethernet

Users can control or monitor WIZ750SR via Ethernet by using the following commands. The user must use UDP or TCP client 7) to send commands, and the port number for processing the commands is 50001.

Network information for command transmission:
UDP / TCP Server : 50001
(User can send the commands by UDP / TCP Client to device)

Ethernet Command Frame Format

Two additional commands are required before sending the command code when controlling the WIZ750SR via Ethernet. All other settings and operations are the same as when sending the serial command code via data UART port.

The two additional commands are MA and PW.

  • [MA] command
    • This field shows the product’s MAC address.
    • In both cases of TCP and UDP, 6-byte MAC address must be included after the 2-byte MA command.
      • When users wish to broadcast only Get Request via UDP8), the relevant field value can be set as the Broadcast MAC address9). Users can receive responses from multiple peers. The search function of the configuration tool is implemented like this
  • [PW] command
    • User must send the setting value of the WIZ750SR after the PW command when using the 'Search ID Code' to distinguish the product group.
    • If the 'Search ID Code' is not used, the PW command and the field between CR & LF (Search ID) must not be blank; enter the value of 0x2010).

The command frame for sending commands via Ethernet
MUST be in the order of MA → PW → (Command x N).

Get Request

When sending a single command

MA [MAC] [CR] [LF] PW [Search ID] [CR] [LF] [Command] [CR] [LF]

When sending multiple commands

MA [MAC] [CR] [LF] PW [Search ID] [CR] [LF] ([Command] [CR] [LF]) * Number of commands
  • The response for ‘get request’ will have the identical format as ‘request’ but include the parameter11).
Set Request

When sending a single command

MA [MAC] [CR] [LF] PW [Search ID] [CR] [LF] [Command] [Parameters] [CR] [LF]

When sending multiple commands

MA [MAC] [CR] [LF] PW [Search ID] [CR] [LF] ([Command] [Parameters] [CR] [LF]) * Number of commands
  • For ‘Set Request’, there is no additional response needed for changing the product setting.
  • If users want to check the modified setting, send the command without parameter at the end of the ‘Set Request frame’; in form of Set + Get Request.

Ethernet Command Examples

Example #1: UDP Get Command Frame
  • When requesting MAC and local IP from multiple devices via UDP
    • Search ID is not used
Request from User

Command Frame

MA [FF FF FF FF FF FF] [CR] [LF] PW [ ] [CR] [LF] MC [CR] [LF] LI [CR] [LF] 

Hex code version of Command Frame

4D 41 FF FF FF FF FF FF 0D 0A 50 57 20 0D 0A 4D 43 0D 0A 4C 49 0D 0A
Response by WIZ750SR

Command Frame

MA [00 08 DC 00 00 11] [CR] [LF] PW [ ] [CR] [LF] MC [00 08 DC 00 00 11] [CR] [LF] LI [192.168.11.2] [CR] [LF] 

Hex code version of Command Frame

4D 41 00 08 DC 00 00 11 0D 0A 50 57 20 0D 0A 4D 43 00 08 DC 00 00 11 0D 0A 4C 49 31 39 32 2E 31 36 38 2E 31 31 2E 32 0D 0A
Example #2: TCP Get Command Frame
  • When requesting the local IP of the device, which MAC address is 00:08:DC:00:00:11, via TCP
    • Search ID is not used
Request from User

Command Frame

MA [00 08 DC 00 00 11] [CR] [LF] PW [ ] [CR] [LF] LI [CR] [LF] 

Hex code version of Command Frame

4D 41 00 08 DC 00 00 11 0D 0A 50 57 20 0D 0A 4C 49 0D 0A
Response by WIZ750SR

Command Frame

MA [00 08 DC 00 00 11] [CR] [LF] PW [ ] [CR] [LF] LI [192.168.11.2] [CR] [LF] 

Hex code version of Command Frame

4D 41 00 08 DC 00 00 11 0D 0A 50 57 20 0D 0A 4C 49 31 39 32 2E 31 36 38 2E 31 31 2E 32 0D 0A
Example #3: TCP Set Command Frame
  • When requesting the local IP of the device, which MAC address is 00:08:DC:00:00:11, via TCP
    • If the Search ID is set to HELLO
    • Or if user wishes to change the local IP to 192.168.11.5
Request from User

Command Frame

MA [00 08 DC 00 00 11] [CR] [LF] PW [HELLO] [CR] [LF] LI [192.168.11.5] [CR] [LF] 

Hex code version of Command Frame

4D 41 00 08 DC 00 00 11 0D 0A 50 57 48 45 4C 4C 4F 0D 0A 4C 49 31 39 32 2E 31 36 38 2E 31 31 2E 35 0D 0A
Response by WIZ750SR
None

When modifying the IP address format12), '.'(dot, 0x2E) must be included like the '192.168.11.5'.


Command list

  • The Set command setting the applicable value will operate if the parameter is included when entering the command.
  • The Get command reading the applicable value will operate if only the command is entered.
  • If the ‘Read only’ sign does not appear, it means the command supports both Get / Set.
  • Write only command is for controlling the product without the parameter13).
  • There is a basic command list14) and an expanded command list15).
  • Settings like IP allocation settings or DNS operation settings via command mode16) require ‘module reboot’ via RT command after the settings are saved via SV command.

Basic Commands

CMD Category Description Type
MC Device Information MAC address RO
VR Firmware version RO
MN Product name RO
ST Operation status RO
UN UART interface(Str) RO
UI UART interface(Code) RO
OP Network Settings Network operation mode RW
IM IP address allocation method
(Static/DHCP)
RW
LI Local IP address RW
SM Subnet mask RW
GW Gateway address RW
DS DNS server address RW
LP Local port number RW
RH Remote host IP address RW
RP Remote host port number RW
BR Data UART Settings UART Baud rate RW
DB UART Data bit RW
PR UART Parity bit RW
SB UART Stop bit RW
FL UART Flow control RW
PT Serial Data Packing Options Time delimiter RW
PS Size delimiter RW
PD Char delimiter RW
IT Options Inactivity timer value RW
CP Connection password enable
(TCP server only)
RW
NP Connection password
(TCP server only)
RW
SP Search ID code RW
DG Serial debug message enable RW
KA TCP Keep-alive enable RW
KI TCP Keep-alive initial interval RW
KE TCP Keep-alive retry interval RW
RI TCP Reconnection interval
(TCP client only)
RW
EC UART Echoback enable RW
TE Command Mode Switch Settings Command mode switch code enable RW
SS Command mode switch code
(3-bytes Hex)
RW
EX Device Control Command mode exit
(switch to data transfer mode)
WO
SV Save device setting WO
RT Device reboot WO
FR Device factory reset WO

Extended Commands

CMD Category Description Type
CA User I/O Settings User I/O pin A type & direction RW
CB User I/O pin B type & direction
CC User I/O pin C type & direction
CD User I/O pin D type & direction
GA User I/O
Status / Value
User I/O pin A status or value Digital out: RW
Digital in: RO
Analog in: RO
GB User I/O pin B status or value
GC User I/O pin C status or value
GD User I/O pin D status or value
SC Status I/O Status pin S0 & S1 operation mode setting RW
S0 Status of pin S0 (PHY link or DTR) RO
S1 Status of pin S1 (TCP connect or DSR)

Command Descriptions

Device Information


MC


  • Format:
    MC[CR][LF]
  • Meaning: Check product’s MAC address
  • Command Type: Read only
  • Return Type: String
  • Return Value:
MAC address with colons(:)
  • Response
  • Without Parameter (Get)
    • In ASCII:
      MC00:08:DC:00:00:01\r\n

VR


  • Format:
    VR[CR][LF]
  • Meaning: Check the product’s firmware version
  • Command Type: Read only
  • Return Type: String
  • Return Value:
Firmware version with dots(.)
  • ⇒ Major version number . Minor version number . Maintenance version number
  • Response
  • Without Parameter (Get)
    • In ASCII:
      VR1.0.0\r\n

MN


  • Format:
    MN[CR][LF]
  • Meaning: Check the product name
  • Command Type: Read only
  • Return Type: String
  • Return Value:
Device model name
  • ⇒ Default: WIZ750SR
  • Response
  • Without Parameter (Get)
    • In ASCII:
      MNWIZ750SR\r\n

ST


  • Format:
    ST[CR][LF]
  • Meaning: Check the product operation status
  • Command Type: Read only
  • Return Type: String
  • Return Value:
Status Description
BOOT Boot mode; Users can update the product setting and firmware.
OPEN Status before TCP connection is successful.
CONNECT Status after TCP connection is successful.
UPGRADE Status during firmware update or DHCP IP allocation.
ATMODE Serial AT command mode status.
UDP UDP mode status.
  • Response
  • Without Parameter (Get)
    • In ASCII:
      STATMODE\r\n

UN


  • Format:
    UN[CR][LF]
  • Meaning: Check product’s UART Interface
  • Command Type: Read only
  • Return Type: String
  • Return Value:
UART Interface Description
RS-232/TTL Device supports UART input/output of RS-232C or TTL signals.
RS-422/485 Device supports UART input/output of RS-422 and RS-485 signals.
  • Response
  • Without Parameter (Get)
    • In ASCII:
      UNRS-232/TTL\r\n

UI


  • Format:
    UI[CR][LF]
  • Meaning: Check product’s UART Interface
  • Command Type: Read only
  • Return Type: Number (0 / 1)
  • Return Value:
Return value Description Remarks
0 Device supports UART input/output of RS-232C or TTL signals. RS-232/TTL
1 Device supports UART input/output of RS-422 and RS-485 signals. RS-422/485
  • Response
  • Without Parameter (Get)
    • In ASCII:
      UI0\r\n





Network Settings


OP


  • Format:
    OP<Parameter>[CR][LF]
  • Meaning: Product’s network operation mode
  • Command Type: Read / Write
  • Parameter / Return Type: Number (0 ~ 3)
  • Parameter / Return Value:
Parameter /
Return value
Meaning Remarks
0 TCP Client mode -
1 TCP Server mode -
2 TCP Mixed mode TCP Server / Client mixed mode
3 UDP mode -
  • Response
  • Without Parameter (Get)
    • In ASCII:
      OP0\r\n
  • With Parameter (Set)
    • No response
    • Change the network operation mode

IM


  • Format:
    IM<Parameter>[CR][LF]
  • Meaning: Product’s IP address allocation method
  • Command Type: Read / Write
  • Parameter / Return Type: Number (0 ~ 1)
  • Parameter / Return Value:
Parameter /
Return value
Meaning Remarks
0 Static IP -
1 DHCP Obtain an IP address automatically
  • Response
  • Without Parameter (Get)
    • In ASCII:
      IM0\r\n
  • With Parameter (Set)
    • No response
    • Change product’s IP address allocation method

LI


  • Format:
    LI<Parameter>[CR][LF]
  • Meaning: Product's IP address
  • Command Type: Read / Write
  • Parameter / Return Type: String of IPv4 address form (including dot)
  • Parameter / Return Value:
Ex> 192.168.11.2
  • Response
  • Without Parameter (Get)
    • In ASCII:
      LI192.168.11.2\r\n
    • In HEX:
      4C 49 31 39 32 2E 31 36 38 2E 31 31 2E 32 0D 0A
  • With Parameter (Set)
    • No response
    • Change product’s IP address

SM


  • Format:
    SM<Parameter>[CR][LF]
  • Meaning: Product’s subnet mask
  • Command Type: Read / Write
  • Parameter / Return Type: String of IPv4 address form (including dot)
  • Parameter / Return Value:
Ex> 255.255.255.0
  • Response
  • Without Parameter (Get)
    • In ASCII:
      SM255.255.255.0\r\n
    • In HEX:
      53 4D 32 35 35 2E 32 35 35 2E 32 35 35 2E 30 0D 0A
  • With Parameter (Set)
    • No response
    • o Change product’s subnet mask

GW


  • Format:
    GW<Parameter>[CR][LF]
  • Meaning: Product’s gateway address
  • Command Type: Read / Write
  • Parameter / Return Type: String of IPv4 address form (including dot)
  • Parameter / Return Value:
Ex> 192.168.11.1
  • Response
  • Without Parameter (Get)
    • In ASCII:
      GW192.168.11.1\r\n
    • In HEX:
      47 57 31 39 32 2E 31 36 38 2E 31 31 2E 31 0D 0A
  • With Parameter (Set)
    • No response
    • Change product’s gateway address

DS


  • Format:
    DS<Parameter>[CR][LF]
  • Meaning: Product’s DNS address
  • Command Type: Read / Write
  • Parameter / Return Type: String of IPv4 address form (including dot)
  • Parameter / Return Value:
Ex> 8.8.8.8
  • Google Public DNS (IPv4)
    • 8.8.8.8
    • 8.8.4.4
  • Response
  • Without Parameter (Get)
    • In ASCII:
      DS8.8.8.8\r\n
    • In HEX:
      44 53 38 2E 38 2E 38 2E 38 0D 0A
  • With Parameter (Set)
    • No response
    • Change Product’s DNS

LP


  • Format:
    LP<Parameter>[CR][LF]
  • Meaning: Product’s port number
  • Command Type: Read / Write
  • Parameter / Return Type: Number (0 ~ 65535)
  • Parameter / Return Value:
Ex> 5000
  • Response
  • Without Parameter (Get)
    • In ASCII:
      LP5000\r\n
    • In HEX:
      4C 50 35 30 30 30 0D 0A
  • With Parameter (Set)
    • No response
    • Change product’s port number

RH


  • Format:
    RH<Parameter>[CR][LF]
  • Meaning: Product’s remote host IP address
  • Command Type: Read / Write
  • Parameter / Return Type: String of IPv4 address form (including dot)
  • Parameter / Return Value:
Ex> 192.168.11.3
  • Response
  • Without Parameter (Get)
    • In ASCII:
      RH192.168.11.3\r\n
    • In HEX:
      52 48 31 39 32 2E 31 36 38 2E 31 31 2E 33 0D 0A
  • With Parameter (Set)
    • No response
    • Change product’s remote host IP address

RP


  • Format:
    RP<Parameter>[CR][LF]
  • Meaning: Product’s remote host port number
  • Command Type: Read / Write
  • Parameter / Return Type: Number (0 ~ 65535)
  • Parameter / Return Value:
Ex> 5000
  • Response
  • Without Parameter (Get)
    • In ASCII:
      RP5000\r\n
    • In HEX:
      52 50 35 30 30 30 0D 0A
  • With Parameter (Set)
    • No response
    • Change product’s remote host port number





Data UART Settings


BR


  • Format:
    BR<Parameter>[CR][LF]
  • Meaning: Baud rate of serial interface (Data UART)
  • Command Type: Read / Write
  • Parameter / Return Type: Number (0 ~ 13)
  • Parameter / Return Value:
Parameter /
Return value
Baud rate Remarks
0 300 -
1 600 -
2 1200 -
3 1800 -
4 2400 -
5 4800 -
6 9600 -
7 14400 -
8 19200 -
9 28800 -
10 38400 -
11 57600 -
12 115200 -
13 230400 -
  • Response
  • Without Parameter (Get)
    • In ASCII:
      BR12\r\n
  • With Parameter (Set)
    • No response
    • Change baud rate of serial interface

DB


  • Format:
    DB<Parameter>[CR][LF]
  • Meaning: Data bit of serial interface (Data UART)
  • Command Type: Read / Write
  • Parameter / Return Type: Number (0 ~ 1)
  • Parameter / Return Value:
Parameter /
Return value
Data bit Remarks
0 7-bit -
1 8-bit -
  • Response
  • Without Parameter (Get)
    • In ASCII:
      DB1\r\n
  • With Parameter (Set)
    • No response
    • Change data bit of serial interface

PR


  • Format:
    PR<Parameter>[CR][LF]
  • Meaning: Parity bit of serial interface (Data UART)
  • Command Type: Read / Write
  • Parameter / Return Type: Number (0 ~ 2)
  • Parameter / Return Value:
Parameter /
Return value
Parity bit Remarks
0 NONE -
1 ODD -
2 EVEN -
  • Response
  • Without Parameter (Get)
    • In ASCII:
      PR0\r\n
  • With Parameter (Set)
    • No response
    • Change parity bit of serial interface

SB


  • Format:
    SB<Parameter>[CR][LF]
  • Meaning: Stop bit of serial interface (Data UART)
  • Command Type: Read / Write
  • Parameter / Return Type: Number (0 ~ 1)
  • Parameter / Return Value:
Parameter /
Return value
Stop bit Remarks
0 1-bit -
1 2-bit -
  • Response
  • Without Parameter (Get)
    • In ASCII:
      SB0\r\n
  • With Parameter (Set)
    • No response
    • Change stop bit of serial interface

FL


  • Format:
    FL<Parameter>[CR][LF]
  • Meaning: Flow control of serial interface (Data UART) / (RS-232/TTL interface only)
  • Command Type: Read / Write
  • Parameter / Return Type: Number (0 ~ 2)
  • Parameter / Return Value:
Parameter /
Return value
Flow control Remarks
0 NONE -
1 XON/XOFF Software flow control
2 RTS/CTS Hardware flow control
  • Response
  • Without Parameter (Get)
    • In ASCII:
      FL0\r\n
  • With Parameter (Set)
    • No response
    • Change flow control of serial interface





Serial Data Packing Options


PT


  • Format:
    PT<Parameter>[CR][LF]
  • Meaning: Data packing of serial interface (Data UART) – Time delimiter17)
  • Command Type: Read / Write
  • Parameter / Return Type: Number (0 ~ 65535)
  • Parameter / Return Value:
0: Not used / 1 ~ 65535: Data packing time (Unit: millisecond)
  • Response
  • Without Parameter (Get)
    • In ASCII:
      PT0\r\n
  • With Parameter (Set)
    • None
    • Change the time delimiter value of serial data packing

PS


  • Format:
    PS<Parameter>[CR][LF]
  • Meaning: Data packing of serial interface (Data UART) – Data size delimiter18)
  • Command Type: Read / Write
  • Parameter / Return Type: Number (0 ~ 255)
  • Parameter / Return Value:
0: Not used / 1 ~ 255: Data packing size (Unit: byte)
  • Response
  • Without Parameter (Get)
    • In ASCII:
      PS0\r\n
  • With Parameter (Set)
    • None
    • Change the data size of serial data packing

PD


  • Format:
    PD<Parameter>[CR][LF]
  • Meaning: Data packing of serial interface (Data UART) - designated character delimiter19)
  • Command Type: Read / Write
  • Parameter / Return Type: 1-byte Character (Hex only)
  • Parameter / Return Value:
00: Not used / Other: Designated character
  • The designated character is not included in data.
  • Response
  • Without Parameter (Get)
    • In ASCII:
      PD00\r\n
  • With Parameter (Set)
    • None
    • Change designated character delimiter of serial data packing





Options


IT


  • Format:
    IT<Parameter>[CR][LF]
  • Meaning: Inactivity timer value for TCP connection close when there is no data exchange
  • Command Type: Read / Write
  • Parameter / Return Type: Number (0 ~ 65535)
  • Parameter / Return Value:
0: Not used / 1 ~ 65535: Inactivity timer value (Unit: second)
  • If the timer is active, the TCP connection closes when there is no data exchange.
  • The timer restarts when there is an Ethernet data exchange before reaching entered inactivity timer value.
  • Response
  • Without Parameter (Get)
    • In ASCII:
      IT0\r\n
  • With Parameter (Set)
    • No response
    • o Change inactivity timer value

CP


  • Format:
    CP<Parameter>[CR][LF]
  • Meaning: TCP connection password enable (TCP server mode only)
  • Command Type: Read / Write
  • Parameter / Return Type: Number (0 / 1)
  • Parameter / Return Value:
0: Not used(Disabled) / 1: Used(Enabled)
  • This option is only when the product is operating as TCP server.
  • If this option is active, the TCP client wishing to connect to the device must send first the TCP connection password and confirmation for actual data to be transmitted.
  • Response
  • Without Parameter (Get)
    • In ASCII:
      CP0\r\n
  • With Parameter (Set)
    • No response
    • Change whether TCP connection password enabled or not.

NP


  • Format:
    NP<Parameter>[CR][LF]
  • Meaning: TCP connection password (TCP server mode only)
  • Command Type: Read / Write
  • Parameter / Return Type: String (up to 8-bytes)
  • Parameter / Return Value:
Default: None(Null)
  • This option is applicable only when product is operating as TCP server.
  • The password can be maximum of 8 characters.
  • Response
  • Without Parameter (Get)
    • In ASCII:
      NP\r\n
  • With Parameter (Set)
    • No response
    • Change TCP connection password

SP


  • Format:
    SP<Parameter>[CR][LF]
  • Meaning: Search identification code
  • Command Type: Read / Write
  • Parameter / Return Type: String (up to 8-bytes)
  • Parameter / Return Value:
Default: None(Null)
  • If this option is active, only the products with matching ID are found via product search by configuration tool.
  • Search ID code can be maximum of 8 characters.
  • Response
  • Without Parameter (Get)
    • In ASCII:
      SP\r\n
  • With Parameter (Set)
    • No response
    • Change search ID code

DG


  • Format:
    DG<Parameter>[CR][LF]
  • Meaning: Serial debug message enable (Debug UART port)
  • Command Type: Read / Write
  • Parameter / Return Type: Number (0 / 1)
  • Parameter / Return Value:
0: Not used(Disabled) / 1: Used(Enabled)
  • If this option is active, the product setting or error message will output via Debug UART port.
  • Response
  • Without Parameter (Get)
    • In ASCII:
      DG1\r\n
  • With Parameter (Set)
    • No response
    • Change whether serial debug message enabled or not.

KA


  • Format:
    KA<Parameter>[CR][LF]
  • Meaning: Keep-alive packet transmit enable for checking TCP connection established
  • Command Type: Read / Write
  • Parameter / Return Type: Number (0 / 1)
  • Parameter / Return Value:
0: Not used(Disabled) / 1: Used(Enabled)
  • If this option is active, the keep-alive packet is sent to the TCP connection peer according to the designated interval(KI / KE).
  • If there is no response from the peer, the TCP connection will close and the socket will initialize (socket open).
  • Response
  • Without Parameter (Get)
    • In ASCII:
      KA1\r\n
  • With Parameter (Set)
    • No response
    • Change whether keep-alive packet transmit enabled or not.

KI


  • Format:
    KI<Parameter>[CR][LF]
  • Meaning: Initial TCP keep-alive packet transmission interval value
  • Command Type: Read / Write
  • Parameter / Return Type: Number (0 ~ 65535)
  • Parameter / Return Value:
0: Not used / 1 ~ 65535: Initial Keep-alive packet transmission interval (Unit: millisecond)
  • The keep-alive packet is sent to the TCP connection peer according to the designated packet transmission interval.
  • Keep-alive packet transmission becomes active only when at least one Ethernet data transmission has been made.
  • Response
  • Without Parameter (Get)
    • In ASCII:
      KI7000\r\n
  • With Parameter (Set)
    • No response
    • Change initial keep-alive packet transmission interval value

KE


  • Format:
    KE<Parameter>[CR][LF]
  • Meaning: TCP Keep-alive packet transmission retry interval value
  • Command Type: Read / Write
  • Parameter / Return Type: Number (0 ~ 65535)
  • Parameter / Return Value:
0: Not used / 1 ~ 65535: Keep-alive packet transmission retry interval (Unit: millisecond)
  • After the first keep-alive packet transmission is done, the next keep-alive packet is sent to the TCP connection peer according to the designated packet transmission interval.
  • Keep-alive packet transmission becomes active only when at least one Ethernet data transmission has been made.
  • Response
  • Without Parameter (Get)
    • In ASCII:
      KE5000\r\n
  • With Parameter (Set)
    • No response
    • Change keep-alive packet transmission retry interval value

RI


  • Format:
    RI<Parameter>[CR][LF]
  • Meaning: TCP client reconnection interval value (TCP client only)
  • Command Type: Read / Write
  • Parameter / Return Type: Number (0 ~ 65535)
  • Parameter / Return Value:
0: Not used / 1 ~ 65535: TCP client reconnection interval (Unit: millisecond)
  • If the TCP connection between the server is not successful during TCP client mode, the interval value between the next connection attempt is set.
  • Response
  • Without Parameter (Get)
    • In ASCII:
      RI3000\r\n
  • With Parameter (Set)
    • No response
    • Change TCP client reconnection interval value

EC


  • Format:
    EC<Parameter>[CR][LF]
  • Meaning: UART Echoback function enable (Data UART port)
  • Command Type: Read / Write
  • Parameter / Return Type: Number (0 / 1)
  • Parameter / Return Value:
0: Not used(Disabled) / 1: Used(Enabled)
  • If this option is enabled, the received serial data becomes Echoback via serial port (Data UART).
  • This function can be used to check what the user enters via serial command mode.
  • Response
  • Without Parameter (Get)
    • In ASCII:
      EC0\r\n
  • With Parameter (Set)
    • No response
    • Change whether UART echoback function enabled or not.





Command Mode Switch Settings


TE


  • Format:
    TE<Parameter>[CR][LF]
  • Meaning: Serial command mode switch code enable
  • Command Type: Read / Write
  • Parameter / Return Type: Number (0 / 1)
  • Parameter / Return Value:
0: Not used(Disabled) / 1: Used(Enabled)
  • This function must be active in order to enter serial command mode via 3-byte command mode switch code.
  • Response
  • Without Parameter (Get)
    • In ASCII:
      TE1\r\n
  • With Parameter (Set)
    • No response
    • Change weather command mode switch code enabled or not

SS


  • Format:
    SS<Parameter>[CR][LF]
  • Meaning: Serial command mode switch code
  • Command Type: Read / Write
  • Parameter / Return Type: String (3-byte hex only)
  • Parameter / Return Value:
Default: 0x2B 0x2B 0x2B 
  • The command mode switch code must be composed of 3-byte(3 characters) hex code.
  • Response
  • Without Parameter (Get)
    • In ASCII:
      SS2B2B2B\r\n
  • With Parameter (Set)
    • No response
    • Change command mode switch code





Device Control


EX


  • Format:
    EX[CR][LF]
  • Meaning: Command mode exit
  • Command Type: Write only (Control)
  • Parameter / Return: None
  • Response
  • Without Parameter
    • No response
    • Command mode exit and switch to data transmission mode
  • While the serial debug message is being used, the following mode switch message will output via Data/Debug UART ports once the switch to data transmission mode is successful.
  • > SEG:GW Mode

SV


  • Format:
    SV[CR][LF]
  • Meaning: Save changed settings
  • Command Type: Write only (Control)
  • Parameter / Return: None
  • Response
  • Without Parameter
    • No response
    • Save changed settings

RT


  • Format:
    RT[CR][LF]
  • Meaning: Device reboot
  • Command Type: Write only (Control)
  • Parameter / Return: None
  • Response
  • Without Parameter
    • No response
    • All operations are closed and device reboot
  • While the serial debug message is being used, the following message will output via data UART
  • > REBOOT

FR


  • Format:
    FR[CR][LF]
  • Meaning: Device factory reset
  • Command Type: Write only (Control)
  • Parameter / Return: None
  • Response
  • Without Parameter
    • No response
    • Reset to device factory default setting
  • The device’s default setting values can be found at WIZ750SR Factory Settings
  • The device reboots after factory reset, like RT command.
    • While the serial debug message is being used, the following message will output via data UART.
    • > REBOOT





User I/O Settings


CA - CD


  • Format:
    Cx<Parameter>[CR][LF] (CA ~ CD)
  • Meaning: User I/O pin setting (type / direction)
  • Command Type: Read / Write
  • Parameter / Return Type: Number (0 ~ 2)
  • Parameter / Return Value:
Parameter /
Return value
I/O Setting Remarks
0 Digital input -
1 Digital output -
2 Analog input -
  • Response
  • Without Parameter (Get)
    • In ASCII:
      CA2\r\n
      CB0\r\n
  • With Parameter (Set)
    • No response
    • Change user I/Os setting





User I/O Status / Value


GA - GD


  • Format:
    Gx<Parameter>[CR][LF] (GA ~ GD
  • Meaning: User I/O pin status or value
  • Command Type: Read / Write
  • Parameter / Return Type: Number (Digital in/out: 0/1, Analog in: 0 ~ 4095)
  • Parameter / Return Value:
I/O Setting Parameter /
Return value
Remarks
Digital in/out 0 Low
1 High
Analog in 0 ~ 4095 12-bit ADC resolution
  • Digital out: R/W
  • Digital in: Read only
  • Analog in: Read only
  • Response
  • Without Parameter (Get)
    • In ASCII:
      GA4095\r\n (Analog input)
    • In ASCII:
      GC0\r\n (Digital input)
  • With Parameter (Set)
    • No response
    • Change user I/O status - High or Low, Digital output only





Status I/O


SC


  • Format:
    SC<Parameter_0><Parameter_1>[CR][LF]
  • Meaning: Set status I/O pin S0(PA_10) and S1(PA_01) operation mode
  • Command Type: Read / Write
  • Parameter / Return Type: Number (0/1)
  • Parameter / Return Value:
  • Parameter_0 (upper byte)
Parameter /
Return value
Meaning Remarks
0 PHY link status Default
1 DTR Data Terminal Ready
(RS-232/TTL only)
  • Parameter_1 (lower byte)
Parameter /
Return value
Meaning Remarks
0 TCP connection status Default
1 DSR Data Set Ready
(RS-232/TTL only)
  • Response
  • Without Parameter (Get)
    • In ASCII: (Connection Status)
      SC00\r\n
    • In ASCII: (DTR / DSR)
      SC11\r\n
  • With Parameter (Set)
    • No response
    • Change status I/O pins operation mode

S0


  • Format:
    S0<Parameter>[CR][LF]
  • Meaning: Status I/O pin S0(PA_10) value
  • Command Type: Read only
  • Parameter / Return Type: Number (0/1)
  • Parameter / Return Value:
  • When operating via PHY link status pin
Return value Meaning Remarks
0 PHY link up -
1 PHY link down -
  • When operating via DTR(Data Terminal Ready) pin
    • Signal that the device communication is ready (RS-232, Output)
    • Connects with peer device's DSR pin
Return value Meaning Remarks
0 The device is not ready -
1 The device ready for communications -
  • Response
  • Without Parameter (Get)
    • In ASCII:
      S00\r\n

S1


  • Format:
    S1<Parameter>[CR][LF]
  • Meaning: Status I/O pin S1(PA_01) value
  • Command Type: Read only
  • Parameter / Return Type: Number (0/1)
  • Parameter / Return Value:
  • When operating via TCP connection status pin
    • TCP server / client / mixed mode only
Return value Meaning Remarks
0 TCP connection established -
1 TCP disconnected -
  • When operating via DSR(Data Set Ready) pin
    • Signal detect that the peer device communication is ready (RS-232, Input)
    • Connect with peer device's DTR pin
Return value Meaning Remarks
0 The peer device is not ready -
1 The peer device ready for communications -
  • Response
  • Without Parameter (Get)
    • In ASCII:
      S10\r\n

2016/04/18 12:52 · hkjung
1) The Configuration tool provided by WIZnet uses the identical command set to control WIZ750SR.
2) For example, when the MC command for checking the MAC address and the VR command for checking the firmware are identical.
3) Data UART port
4) Command mode switch trigger code via Data UART port
5) Char '+++'
6) Conversely, the serial command after mode switch must end with CR or LF.
7) Users must use UDP or TCP client because the UDP or TCP server is operating to handle the device commands.
8) Data is sent to the broadcast IP address 255.255.255.255, and data can be sent to all peers in the same network.
9) FF:FF:FF:FF:FF:FF
10) Hex value 0x20 means ‘gap’ in ASCII code.
11) The response for ‘Get Request’ has the same form as ‘Set Request’.
12) IPv4 address form like IP address, Gateway address, subnet mask, DNS server address, or Remote IP address.
13) Save setting, reboot, switch mode, factory reset and Etc.
14) WIZ107/108SR sync command list, excluding [UI] command
15) WIZ750SR exclusive command list
16) When the remote peer address is changed from IP address to domain
17) The received serial data is collected until the designated time is lapsed and will be sent all together via Ethernet. This time starts counting when receiving the serial data stop, and if additional serial data is received before the designated time is lapsed, the count restarts.
18) The received serial data is collected until the designated data length is reached and will be sent all together via Ethernet.
19) The received serial data is collected until the designated character is received and will be sent all together via Ethernet.
products/wiz750sr/commandmanual/start.txt · Last modified: 2016/11/14 11:13 by hkjung