User Tools

Site Tools


osh:wizfi310_shield:start

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
osh:wizfi310_shield:start [2017/04/25 15:12]
jeongsk [Overview]
osh:wizfi310_shield:start [2018/09/21 09:19] (current)
jeongsk [ETC]
Line 32: Line 32:
     * CP2104-GM     * CP2104-GM
     * Micro USB B Type Connector     * Micro USB B Type Connector
-  * UART Selector ​J1, J2, J3 +  * UART Selector 
-  * Built-in ​Sensor+    * J1, J2, J3 
 +    * 2.54mm Pin Header 
 +  * Built-in ​Sensors
     * Temprature/​Humidity sensor : DHT11     * Temprature/​Humidity sensor : DHT11
     * CDS Sensor : GL5537     * CDS Sensor : GL5537
-  * Built-in Tact SW +  * Built-in Tact Switchs 
-    * System Reset SW SW4 +    * System Reset SwitchSW2 
-    * WiFi Reset SW : SW3 +    * WiFi Reset Switch: SW3 
-    * WiFi Function ​SW SW2 +    * WiFi Function ​SwitchSW4 
-  * Built-in LED+  * Built-in LED Indicators
     * D13 LED     * D13 LED
-    * WizFi310 MODE LED +    * WizFi310 MODE/WiFi LED 
-    * WizFi310 ​WiFi LED +    * WizFi310 ​RXD/TXD LED 
-    * WizFi310 ​RX/TX LED +  * Built-in Level Shifters
-  * Built-in Level Shifter+
     * The voltage of the RXD/TXD signal changes according to the main board platform voltage.     * The voltage of the RXD/TXD signal changes according to the main board platform voltage.
-  * Built-in DIP Switch+  * Built-in DIP Switchs
     * UART RXD/TXD Selector : SW1     * UART RXD/TXD Selector : SW1
     * Digital/​Analog PIN Selector : SW5     * Digital/​Analog PIN Selector : SW5
Line 60: Line 61:
 ===== H/W Configurations ===== ===== H/W Configurations =====
 ==== DIP Switch Configurations ==== ==== DIP Switch Configurations ====
-=== SW2 - RXD/TXD Selector ===+=== SW1 - RXD/TXD Selector ​DIP Switch ​===
   * **ON** : RXD/TXD of WizFi310 connect to USB   * **ON** : RXD/TXD of WizFi310 connect to USB
     * It is possible to communicate with WizFi310 using USB.     * It is possible to communicate with WizFi310 using USB.
Line 71: Line 72:
   Pin 2 : TXD   Pin 2 : TXD
  
-=== SW6 - RTS/CTS Selector ===+ 
 +=== SW6 - RTS/CTS Selector ​DIP Switch ​===
   * **ON** : RTS/CTS of WizFi310 connect to D6 and D7   * **ON** : RTS/CTS of WizFi310 connect to D6 and D7
   * **OFF** : RTS/CTS of WizFi310 not connect to anywhere   * **OFF** : RTS/CTS of WizFi310 not connect to anywhere
Line 80: Line 82:
   Pin 2 : CTS - D7   Pin 2 : CTS - D7
  
-=== SW5 - Aruduino Pin Selector ===+ 
 +=== SW5 - Aruduino Pin Selector ​DIP Switch ​===
   * **ON** : Connect to Arduino Pin   * **ON** : Connect to Arduino Pin
   * **OFF** : Not connect to anywhere   * **OFF** : Not connect to anywhere
Line 89: Line 92:
   Pin 3 : D9 - WizFi310 Reset Pin   Pin 3 : D9 - WizFi310 Reset Pin
  
-=== UART Jumper ​Configurations ​===+ 
 +=== UART Selector ​Jumper ===
   * **It can be used when SW2 is OFF.**   * **It can be used when SW2 is OFF.**
   * You have to specify the desired Arduino pin, use Jumper Cap to connect J1 to J2, and J3 to J2.   * You have to specify the desired Arduino pin, use Jumper Cap to connect J1 to J2, and J3 to J2.
Line 99: Line 103:
   J2 : D0 ~ D8   J2 : D0 ~ D8
   J3 : TXD   J3 : TXD
 +
  
 ---- ----
osh/wizfi310_shield/start.1493100774.txt.gz · Last modified: 2017/04/25 15:12 by jeongsk